top of page

SWIP INTERNAL WALL INSULATION

Internal Wall Insulation in Durham

Dampline installs SWIP internal wall insulation for suitable solid-brick, stone and masonry homes across Durham and County Durham. We check the wall construction, ventilation and moisture condition before recommending a system.

INTERNAL WALL INSULATION SUITABILITY

Which properties can benefit?

Internal wall insulation is fitted to the inside face of an external wall. It’s commonly considered for solid-brick terraces, stone cottages and other properties with no cavity suitable for insulation.

What can it improve?

A suitable system can reduce heat loss, make cold wall surfaces warmer and help rooms stay comfortable in winter. The exterior brick or stone remains visible, while the new lining slightly reduces the room’s dimensions.

Could insulation make your walls warmer?

Good to know

A cold or damp wall can have several causes. We check whether insulation is suitable and flag leaks, damaged masonry or ventilation problems that need attention first.

INTERNAL WALL INSULATION ASSESSMENT

What we check before work starts

Wall construction

We look at the wall material, thickness and condition, including whether there’s a cavity and whether it’s suitable for insulation.

Moisture and exposure

We look for signs of water ingress and consider ventilation, indoor moisture and exposure to wind-driven rain.

Room layout and details

We review reveals, adjoining walls, floors and ceilings, along with fixtures that may need moving to accommodate the system.

Dark roofing membrane being laid over a timber deck on a flat roof.

SWIP INTERNAL WALL INSULATION

How we insulate the wall from the inside

We specify the SWIP system for the property, prepare the existing wall and fit the insulation and lining with attention to the points where walls, floors and ceilings meet.

The SWIP insulation system

SWIP combines thermally engineered composite studs with closely fitted Earthwool insulation batts. The studs are designed to reduce thermal bridging through the frame, which is where heat can otherwise escape more readily.

We select the build-up around the property’s construction and the thermal performance needed. It includes the specified vapour-control layer and internal lining, leaving a smooth wall ready for finishing and decoration.

Preparing the walls and planning the details

We assess the existing wall and finishes before fitting the system. Identified damp defects and unsuitable finishes need to be addressed first. Depending on the room, radiators, sockets, skirting boards, window boards and other fixtures may need to be removed or repositioned.

• Plan the build-up around window and door reveals.
• Check how the insulation will meet floors, ceilings and adjoining walls.
• Allow for the reduction in room dimensions when planning fixtures and finishes.

Fitting the insulation and finishing the wall

We fit the composite studs and closely fitted insulation batts to form a continuous thermal layer. The specified vapour-control layer and internal lining are then installed, with particular care around reveals and junctions where gaps can leave cold spots.

Dampline’s service is led by Tony Jones, a SWIP Approved Contractor who holds an NVQ in Internal Wall Insulation, an ABBE Level 3 qualification relating to older and traditional buildings, and a Level 3 Retrofit Assessor qualification. Tony has personally worked on more than 1,000 internal wall insulation installations.

INTERNAL INSULATION AND DAMP

Condensation, damp and ventilation

Warmer internal wall surfaces can reduce surface condensation where cold masonry contributes to the problem. High indoor humidity, poor ventilation, leaking pipes, defective gutters and penetrating rain each need to be investigated in their own right.

If there are signs of damp, we check the cause before recommending insulation. That helps avoid covering an active moisture problem and makes it clear which repairs or ventilation improvements may be needed first.

Older properties across County Durham

Stone type, wall thickness, mortar, pointing and exposure all affect how traditional walls handle moisture. A sheltered brick terrace and an exposed stone cottage may need different specifications, even if both have solid walls.

We assess suitable properties across Durham City, Chester-le-Street, Stanley, Consett, Bishop Auckland, Crook, Spennymoor and surrounding communities. The recommendation depends on the individual building, its condition and how it is used.

What affects the recommendation?

INSULATION SERVICES FAQS

Your insulation questions, answered.

Find out what we install, how we check suitability and what to do if you already have insulation or a damp problem.

RELATED INSULATION AND DAMP SERVICES

Explore other options for your property

If your property has cavity walls or you’re seeing signs of damp, these services can help you work out the next step.

Cavity Wall Insulation

Explore ThermaBead bonded-bead insulation and the checks we carry out to see whether a wall cavity is suitable.

Damp Surveys

Find out whether cold surfaces, condensation or water getting in could be contributing to damp in your property.

Ready to discuss your property?

Enquire now for friendly and professional advice about your issue or property.

bottom of page