top of page

WALL TIE REPLACEMENT

Wall Tie Replacement in Durham

Dampline provides wall tie inspections, replacement and associated masonry repairs across Durham and County Durham. We investigate cracked, bulging and unstable cavity-wall masonry to determine whether existing ties have corroded, failed or become inadequate.

WALL TIE FAILURE SIGNS

What do wall ties do?

Wall ties connect the inner and outer leaves of a cavity wall. Their condition, spacing and fixings help determine how well the leaves are held together.

Signs worth investigating

Horizontal cracks along mortar joints, bowing or bulging brickwork and movement around openings can warrant inspection. Corrosion, missing ties or poor original installation may be involved.

Could the wall ties be failing?

Good to know

Cracks can have several causes. We look at the wall and inspect the cavity where appropriate before deciding whether ties need replacing.

CAVITY WALL TIE INSPECTION

What we check before work starts

Cracks and wall movement

We look at the crack pattern, condition of the masonry and any visible movement around openings.

Borescope checks

A borescope can help inspect accessible ties, cavity condition and evidence of corrosion or poor installation.

Construction and fixing points

We assess the wall materials and condition to inform the remedial tie type, length and fixing positions.

Exterior red-brick wall corner showing the brick courses and mortar joints.

REMEDIAL WALL TIE INSTALLATION

How we replace failed wall ties

We use the inspection findings to specify the new ties and decide whether existing ties need isolating or masonry needs reinstating.

Installing remedial wall ties

How Wall Ties Are Replaced
Wall tie replacement normally involves installing new remedial ties rather than dismantling the complete cavity wall. The exact method depends on the substrate. Brick, block, stone and unusual construction may require different remedial tie systems.

Stainless-Steel Remedial Wall Ties
Stainless steel is commonly used for remedial wall ties because it provides durable corrosion resistance within the cavity environment. Dampline selects the remedial system according to the actual wall rather than installing one tie type in every property.

Isolating ties and making good

Isolating Corroded Wall Ties
Installing new ties restores the connection between the masonry leaves, but badly corroded original ties can continue expanding within the mortar joints. Where the existing ties are causing active cracking, isolation may be required to reduce their continuing effect on the external leaf. The appropriate method depends on the original tie type, location and accessibility.

Repairing Cracks After Wall Tie Replacement
Cracked mortar and damaged bricks may require repair after the remedial ties have been installed and the cause of movement has been controlled. Cracks should not simply be filled before the wall-tie defect is investigated. Cosmetic pointing over continuing corrosion or movement is unlikely to provide a lasting repair.

Working around insulation and openings

Wall Tie Replacement and Cavity Insulation
Existing cavity insulation can affect inspection, drilling and installation. Mineral wool, bonded beads, rigid boards and debris may restrict visibility or access to the original ties. Dampline considers the insulation type and condition during the assessment. Where material is wet, defective or preventing necessary remedial work, further investigation or localised removal may be required.

Wall Ties in Brick and Stone Properties
Remedial ties can be required in brick, block and certain stone-faced cavity walls, but the correct system varies with the substrate. Irregular stone, rubble-filled sections, soft mortar and wide cavities may require additional investigation. Installation positions and embedment cannot always be determined using the assumptions applied to uniform modern brickwork.

Wall Tie Replacement Around Windows and Doors
Openings interrupt the normal wall-tie pattern and can create vulnerable masonry areas. Cracking around windows may also be caused by failed lintels rather than wall ties. If the lintel is responsible, adding remedial ties alone will not resolve the crack. The correct structural defect must be addressed.

WALL TIE REPAIR CONSIDERATIONS

Bowing and structural movement

Where the outer wall is bowing or bulging, the extent of movement and condition of the masonry need assessing before work is specified. Significant movement may need structural engineering input and a wider repair plan.

Wall tie replacement costs

Cost depends on the wall area, access, cavity construction and number of ties required. The quote can also include isolating corroded ties, working around existing insulation or openings and repairing affected mortar joints or masonry.

What affects the recommendation?

MASONRY REPAIR FAQS

Your masonry repair questions, answered.

Find out when a wall may need repointing, what causes bricks to crumble and how we assess cracks and damp.

RELATED MASONRY AND DAMP SERVICES

Explore related services

These services may help if the inspection identifies related defects or work elsewhere on the property.

Cavity Wall Insulation

See why existing ties, moisture and cavity condition matter before insulation is installed.

Brick & Stone Repointing

Explore local mortar repairs where masonry needs making good after tie work.

Ready to discuss your property?

Enquire now for friendly and professional advice about your issue or property.

bottom of page